Dama outdoor

Installation manual

Last updating 04 of July 2024

DAMA OUTDOOR is a wireless outdoor siren with power up to 112 dB at 1 meter, the flashing light is red high intensity that ensures a vision from afar. It installs and configures quickly thanks to easy-fix support and ensures a 5-year life with pre-installed batteries. The aesthetic line is pleasant thanks to a careful design study.
It is made of weather and UV resistant ABS. Thanks to the particular design of the gaskets guarantees a maximum water tightness and is in compliance with IP55.

DAMA OUTDOOR works within the D’AVINCI system with a range of up to 1500 meters (in free space) by connecting, via radio, directly to the Lisa control panel or via Automa repeater. The communication is bidirectional (transmission/reception) with the indication of confirmation of receipt and command. In the case of obstacles such as walls, objects, etc. the range is reduced. It uses a high-efficiency piezoelectric transducer that can deter any attackers. It also has tamper anti-tampering able to instantly signal the removal from the wall and the opening of the body.

The communication protocol, like the connections between all the components of the system, is the GENIO, encrypted and protected from interception.
Configuration takes place via D’AVINCI app downloadable for free from IOS and Android.

The Siren operates on two frequencies in the 868 MHz band, automatically and dynamically positioned on the one that is free or less interfered.

To add a device to the control panel, in the D’AVINCI app  ¹

1. Select the Tab Device ²  
2.  Click on Add Device 
3.  Name the device
4. Insert the serial number of the device shown on the label  or click on icon  to scan the code via the app.
5. Select the associated Room for the device.

6. Click Add – a countdown will start.

7. Remove the tab from the batteries, so as to Power the device (see installation phase of the device).
   The siren LEDs will emit flashes when it is switched on.

   When paired with the control panel, the siren will appear in the list of devices in the AVINCI App.

   The connection request to the Control Panel is transmitted for a short period of time as soon as the device is switched on.

   If the connection to the AVINCI control panel fails, turn off the detector for 5 seconds and repeat the procedure.

¹ Installer privileges are required.

² To start the configuration procedure, the device must be within the radio communication zone of the associated Control Panel.

Make sure that you have selected the ideal installation location according to the guidelines in this manual.
The place of installation of the siren affects the connection with the control panel and any obstacles between the devices can block the transmission of the radio signal. Such obstacles can be walls, floors or large objects within a room. Be sure to install the siren on a flat surface, in a position not easily accessible in such a way as to minimize the risk of tampering.

If the signal level is low, stable operation of the safety system is not guaranteed. Please take any measures to improve the signal quality!

First, try to move the device

If this is not enough and the device still has a low or unstable signal strength, use a radio signal repeater.

To install the device:

Remove the tabs from the batteries.

The detector settings can be changed in the D’AVINCI app (Installer privileges are required):

1. Go to device tab
2. Select the device from the list.
3. Go to settings by clicking on the icon (gear)

DEVICE NAME
Siren name , display in the device list and as notification text.
It can hold up to 24 characters
ROOM
Selecting the virtual room to which the device is assigned the environment name appears in notifications.
Note: Changing this parameter requires Administrator privileges

SIREN VOLUME
Allows you to adjust the acoustic intensity of the device.
– Disabled
– Low
– Normal
– High

REPORTING TIME
Sets the duration of the device’s signal.
[ 5 – 180] seconds

SOUND TONE
Sets the sound tone of the siren.
[ 1 – 8] seconds

TAMPERING ALARM
Allows you to enable/disable the device acoustic warning in case of tampering

ALERT STATUS ARMED
Enables/disables the visual indication of the device when it is armed.
– Never: visual signalling is not enabled
– Inserted: visual signalling is enabled to implant inserted.

ACOUSTIC SETTINGS
Enables/disables the acoustic indication of the device.
–Switched on/off: If enabled, the siren warns of on and off
with a light indication and a short beep.
-Switched on/off Stay : if enabled, the siren warns of the insertion and the
Stay mode deactivation with a light indication and a short acoustic signal.
-Input delay: If enabled, the siren will sound, with a short beep, a
late entry
-Output delay: if enabled, the siren beeps for a short delay
on exit.
-Stay mode input delay: if enabled, the siren signals with a short signal
acoustic, a delay at the entrance in Stay mode
-Stay mode output delay: if enabled, the siren signals with a short signal
acoustic, an outgoing delay in Stay mode

REPEATER
Enables the connection of the device to the system through a repeater ( Automa).
– Repeater number: indicates the number of the repeater to which the device is associated.

VERIFICATION OF RADIO CONNECTION
Enables alarm warning in case of failure to communicate with the
central. If disabled, the report of failure to connect to the central will be
exclusively archived.
Ping interval: time interval, in seconds, between a transmission of
survival and the next in the absence of activation.
– [ 12 :600 ] seconds
Ping number: number of connection attempts before failure report
radio communication
– [ 1 : 15 ]

RADIO SIGNAL INTENSITY TEST
With this function, the device after pressing the START button processes a test where it will indicate the signal level , flashing the led n times depending on the result obtained.(1-4)

TEST VOLUME
With this function, the device after pressing the START button will perform an acoustic test.

EXCLUDE DEVICE
By selecting this button, the device is completely excluded from the operation of the
system, not signaling alarms or events.
No: The device works normally and transmits all events/alarms

All: The device does not execute the sent commands. The system ignores the
device and its notifications.

Lid Only: The system ignores notifications about activating the (tamper) button
tampering with the device.

REMOVE DEVICE
Dissociate the detector from the Control Panel, removing it from the app and deleting the device settings.

To display the signal strength select the card Devices and the signal level field GENIO

0 = No radio signal, no connection to control panel.
• = Poor radio signal, unstable connection with the Control Panel , operation of the detector not guaranteed.
• • = Low radio signal, low signal strength.
• • • = Good radio signal, good signal strength.
• • • • =  Excellent radio signal, optimal signal strength.

Check the radio signal strength before the final installation of the device. In case of low or unstable signal it is recommended to use the Automa repeater.

1. Access the D’AVINCI application
2. Select the Control Panel on which the detector is associated
3. Go to Devices tab
4. Select the detector

Release the Siren from the stirrup.

Reassemble the Siren on its bracket and tighten the screw to lock it.

Copyright 2023 - 2024 – D’AVINCI Security Products Srl – C.F. e P.IVA 12908830966 – All right reserved. || privacy policy